20 best waterproofing

The waterproofing vulcanized film is made of synthetic rubber, mainly intended for decorative or fish ponds, as well as swimming pools. The main features of the rolled material are high elasticity, resistance to ultraviolet, ozone, flexibility at low temperatures, and resistance to chemical compounds. At the same time, it is completely safe and does not contain toxic compounds.

According to the owners, this waterproofing additionally shows good soundproofing and airtight properties, is quite wear-resistant and tolerates heat well - it can be applied on the floor in the steam room. It is optimal for waterproofing large areas, and can also be laid on concrete or brick with a geotextile protective underlay. The only drawback is the cost, but the reliability and impeccable quality of the rubber film are worth it.

This film, designed for waterproofing surfaces and structures, is a gray rolled fabric, which is covered with a protective layer with the addition of a UV stabilizer. It can also be used as a roofing material for pitched roofs, indoors to protect against excess moisture in the bathroom, evaporation and condensate. The main advantage of such a film is that it is immediately made with an adhesive base capable of tightly isolating overlaps or joints, in addition, no additional costs, including time, for fasteners are required.

You can use such material on the outer walls of the house for a maximum of 1-2 months, but the sooner the protective layer is laid, the longer the life of the membrane. Customer reviews note good heat-saving properties, resistance to wind, rain, sunlight.

Diffusion waterproofing in the form of a rolled membrane protects not only from high humidity, but also from dirt, dust, ultraviolet radiation and other adverse environmental influences. Created from polyethylene threads and covered with a protective film, it is ideal for roofing roofs, protecting wooden or brick walls, concrete or other floors inside different rooms - in the bathroom, sauna.

Thanks to the double-sided protective coating, it can be laid on either side. Also, of the advantages, users in their reviews indicate ease of installation - the waterproofing must be fixed with adhesive tape (it is better to use original products).This material is designed for roofing, and for laying outside a heated room, for example, in basements or swimming pools, the manufacturer recommends using other series of its membranes.

You can use waterproofing of this series for roofs, during construction in wooden interfloor ceilings, for walls in conditions of high humidity, for example, in a bath, pool or steam room. This rolled roofing material exhibits excellent resistance to extreme temperature fluctuations. It has 2 layers, one is a polypropylene film, and the second is a high-strength fabric, which provides maximum water resistance, vapor permeability and strength. Reliably protects against water, condensate and vapors.

Feedback from owners who have used it for 3-4 months as a temporary roof covering confirms its practicality. As a membrane for metal roofing, this waterproofing can safely be considered one of the best solutions. Indoors, the period of operation is not limited. At the same time, it is also successfully used to protect floors made of concrete, brick or wood structures.

This roll material is intended for roofing, and although it is not entirely suitable for waterproofing brick and concrete walls, floors, some use a membrane there as well. It can be laid in one layer, easily boiled with hot air, forming a strong and airtight seam.The basis of a high-quality membrane is a PVC film reinforced with a reinforcing mesh based on polyester - it gives high strength, while maintaining the flexibility of the material.

Thanks to special additives in the raw materials, the coating protects not only from moisture, but also from chemical compounds, ultraviolet radiation, and temperature extremes. In combination with traditional roofing materials (metal tiles or corrugated board), it shows the longest service life and is easy to restore. Judging by customer reviews, the reliability of BIGTOP V-RP (1.2 mm thick) allows the membrane to be successfully used in preparatory work as a temporary roof.

The basis for this rolled waterproofing material is fiberglass, which is impregnated with polymers and bitumen, protected from both sides by a layer of spunbond. Its main purpose is to protect structural elements from the rise of capillary moisture. Among the advantages are UV resistance, long service life (from 50 years), non-rotting base, the ability to choose a roll of different widths to reduce waste and facilitate the installation process.

Based on the reviews left by different users, the membrane has a universal purpose and is used in arranging waterproofing of roofs, walls, floors made of concrete, wood, brick and other materials. Thanks to strong sealing, TechnoNIKOL Master reliably protects building elements from moisture and mold. Distinguished by high elasticity, it has proven itself well in working with complex architectural forms.

This high-quality rolled waterproofing is suitable for both horizontal and vertical laying on the plinth of buildings, floors, basement walls, foundations, balconies. It is applied with a cold method due to the self-adhesive bottom layer, while having a thickness of 1.5 mm, it does not create an excessive load on fragile structures. Reliably protects against condensate and groundwater, when used internally creates a waterproofing of surfaces made of concrete, boards or bricks from capillary moisture.

Judging by the reviews, the installation of such a membrane is easier than analogues - it consists in simply rolling the roll. Due to its minimal thickness, it is flexible enough to be used in waterproofing structures with complex shapes. It does not require curing, quickly adheres to the substrate (requires cleaning from dust and dirt), and, in general, reduces installation time by about 2 times compared to standard waterproofing types.

The use of this waterproofing material prolongs the life of buildings and structures, protects them from premature destruction from the effects of the external environment - mainly water. It is produced in rolls, used to protect against groundwater that can cause the destruction of the foundation. It is also used in basements on the floor, to protect concrete or brick walls, roofing garages and industrial buildings. In addition to water, it also prevents the penetration of various aggressive chemical components.

The basis for this material is a fiberglass base, which is covered with an astringent bituminous layer and solid filler. Thanks to this compound, judging by the reviews, it resists moisture well, is able to maintain strength at low and high temperatures, and is resistant to ultraviolet radiation. It is also noted that this waterproofing is easy to work with - laying can be done on your own.

Such rolled waterproofing is used in two-layer systems for roofing roofs, floors, walls. It can be used both for residential and industrial buildings and buildings, as well as for covering swimming pools, foundations, attics, basements as a protection against groundwater and moisture. For industrial purposes, it is excellent for covering tunnels in transport construction. It is made on the basis of fiberglass impregnated with bitumen, has a coarse-grained dressing on top, and a built-up layer with special corrugation on the bottom side.

In their reviews, buyers indicate the resistance of this material to heat - it tolerates temperatures up to 90 degrees. At the same time, it retains its elasticity even at frosts down to -30.The price fully meets expectations - the owners are satisfied with the quality of waterproofing, which determines the durability in operation.

Roll material for waterproofing of this series is designed for roofing, as well as creating a protective layer of structural elements from condensate and moisture. It is universal, it can cover not only any floors, foundations, plinths and walls made of wood, concrete, brick, but also communication systems. It features minimal consumption and affordable price, which reduces the cost of waterproofing. In this case, one layer with a slight overlap is enough. It provides a high degree of moisture protection, and due to its low weight it does not weigh down the structure, is resistant to heat and frost, and is quite maintainable.

In their reviews, buyers also note its fire safety, the absence of excessive heating in summer, styling without special skills and devices. Many use such material as waterproofing in basements and outbuildings, to protect the building from the outside and the roof of garages.

One-component polyurethane-based foundation waterproofing is used to create a protective layer in building structures.It is based on a hydrophobic elastomer resin, which is combined with fillers that create a strong moisture barrier after curing. The main area of ​​application is the processing of beams and ceilings made of concrete, tanks (wells, tunnels), basements, parking lots. The key advantages of this liquid coating mixture are high penetrating power and retention of elasticity in the cold.

The composition is ready for use, and, judging by the reviews, it is fully capable of providing not only reliable adhesion, but also environmental safety. The mixture completely hardens in about 6 hours, and polymerization takes up to 7 days. After the end of this process, it forms the most reliable and dense layer, not affected by precipitation, condensate or groundwater.

When using such a penetrating cementitious waterproofing, moisture can be effectively prevented from entering surfaces with pores and cracks up to 0.4 mm in size. The scope of such a liquid coating mixture is not so wide - coating any reinforced concrete or concrete structures to increase their water resistance. Not suitable for natural stone or brick, or objects with large cracks or wide joints.

The mixture has the function of "self-healing" - in the process of solidification it forms dendritic crystals, which completely fill the pores and microcracks. Judging by the reviews, the average consumption is about 1 kg of the finished solution per square meter. m. Penetrating ability - up to 1 m in the thickness of concrete. Of the other advantages, rapid solidification and increased resistance to low temperatures are particularly noted.

Hydroplug - a special waterproofing designed specifically to eliminate pressure leaks, is of a penetrating type, suitable for a base made of brick, stone or concrete. The mixture is made on the basis of quartz sand, cement and includes additives that fill the capillary pores of the base. With its help, you can most effectively isolate both ordinary concrete pouring and reinforced concrete slabs.

The liquid penetrating mixture is applied without special equipment, immediately seizes and immediately hardens. She is treated with wells and basements, foundations and pools, fountains, roofing, sewage treatment plants, self-leveling floors and walls in private homes. According to reviews, coating waterproofing does not require drying time, increases the frost resistance of the base and its water resistance, does not contain sulfates and chlorides, which can cause reinforcement corrosion and lead to the destruction of reinforced concrete structures.

High-quality cement-based penetrating waterproofing is optimally suited for objects and structures that are in constant or frequent contact with water. It is used for outdoor work - foundation, walls, floors made of concrete or brick, balconies, terraces. As a protective layer, it can be applied under the roof of flat roofs, as well as for internal strengthening of basements and cellars, walls of wells to protect against groundwater. The material also shows maximum resistance to sulfates and chlorides.

Among the advantages of this liquid coating waterproofing is improved adhesion to the base.This feature allows you to create a completely waterproof layer, durable and strong. The effect is achieved due to the fact that, after hardening, the solution forms crystals that fill microcracks and pores by 100%. According to reviews, OSMOGROUT is easy to apply, does not flow and is extremely convenient to use.

Penetrating waterproofing mortar contains chemical agents that provide a high degree of adhesion, the ability to use outdoors and indoors, including operation at sub-zero temperatures. For repair purposes, it is used to treat microcracks, seams and pores on the surfaces of walls, foundations and floors made of brick or concrete, in basements to protect against groundwater, wells and other structures.

The cement mortar is resistant to high and low temperatures, dries quickly enough, reliably protects the application site from the penetration of water and condensate. Liquid waterproofing does not require long-term preparation of the base, it is quickly mixed to a homogeneous mixture, in which no inclusions remain. According to reviews, the material consumption is quite economical - about 8 kg with a layer thickness of only 5 mm per square meter. m.

Eunice Hydroplast is ideal for seamless waterproofing of masonry, concrete walls, foundations and other substrates. It can be used to cover elements that are in direct contact with water - the walls of pools, wells. After drying and gaining proper strength, it is able to prevent flooding of basements and basements with groundwater. Also suitable for covering a self-leveling roof to increase resistance to natural precipitation.

Coating waterproofing has increased frost resistance in comparison with analogues. The permissible layer thickness is up to 4 mm, while the solution is consumed sparingly - you can work with both a regular brush and a spatula. With the right ratio of dry mix and water, liquid waterproofing forms a plastic mass with a uniform consistency, which ideally fits on uneven surfaces.

Thanks to this cement coating waterproofing, it is possible to achieve high water resistance of various concrete and brick bases on balconies, in shallow pools, on terraces, in basements, facades and foundations. It is also used in wells to protect against groundwater. Ideal for indoor use - walls and floors in kitchens and bathrooms after such treatment will not become damp and absorb moisture. The main advantages of this slurry are that it retains vapor permeability, is resistant to cracking, is ductile and can be applied directly to wet substrates. At the same time, GLIMS WaterStop is a safe and environmentally friendly material.

Most of the reviews directly indicate the most economical consumption - about 1.4 kg per 1 square meter of area, a simple manual application method, a wide temperature range of application and the ability to lay a layer of no more than 3 mm at a time.

Quality waterproofing helps create a waterproof barrier at a fair price. It has a high plasticity of the solution due to special additives, which also affect the resistance of the treated elements to mechanical damage, protects the base from low temperatures and steam, condensate, mold. Such a liquid coating can be used to cover the foundations and facades of buildings, in basements, on balconies and terraces, in indoor pools and tanks, for floors and walls that come into contact with moisture (in the bathroom). Ideally lays down on the bases from concrete or a brick.

Dry cement mixture is not at all demanding in work. The owners in their reviews indicate that it mixes well and quickly, easily fits at a consumption of about 4 kg per square (if the layer thickness is not more than 3 mm). At the same time, during the first 24 hours, it must be moistened and protected from frost and direct sunlight.

This coating type mixture can be successfully used both for waterproofing and for minor repair (construction) work - as glue, mortar or putty for sealing fillet welds, screeds.Easy to apply - mixes until smooth, easy to apply on walls and floors made of bricks and concrete, quickly sticks and does not drain if you follow the instructions for preparing the mortar. After hardening, it forms a monolithic and durable coating layer, resistant to moisture.

BERGAUF Hydrostop can be used for waterproofing garages, basements, swimming pools (with a maximum depth of 5 m), facades, foundations, as well as for floor screed in bathrooms and other areas with high humidity. Customer reviews fully confirm the characteristics declared by the manufacturer. The layer dries completely in 48 hours, in finished form it can be stored for no more than 180 minutes, but it is categorically not recommended to work at low temperatures.

The waterproofing mixture of this series is mainly used to protect against moisture bases that do not contain gypsum - walls, floors, foundations, basements, plinths, as well as reinforced concrete ceilings both inside and outside the structure. Among the features of this liquid solution is the inclusion of a color indicator in the composition, which allows you to control its application to the surface, a high class of vapor and water resistance, the possibility of using for laying "warm floors" in the bathroom, and frost resistance. Due to its environmental friendliness, it can be used for drinking water tanks (the same wells) or pools, while it is resistant to alkaline solutions and salts.

Additionally, this coating liquid waterproofing prevents the spread of mold and fungus, due to its optimal penetrating ability, it fills the voids of the upper layer of brick and concrete.Working with it, judging by the reviews, is very easy - Ceresit CR 65 forms a thin uniform layer when working with a conventional spatula.